KH 4410 LAMINATOR - Laminator LERVIA - Free user manual and instructions

Product Type	Laminator
Brand	LERVIA
Model	KH 4410
Power Supply	220-240 V ~ 50 Hz, 308 W
Laminating Speed	Approx. 0.4 m/min
Maximum Laminating Thickness	1 mm
Maximum Pouch Width	230 mm
Maximum Pouch Thickness	2 x 125 microns (250 microns)
Laminating Modes	Hot and Cold
Preparation	Preheating with green LED "Ready" indicator
Anti-Jam System	Yes (ABS)
Intended Use	Paper or cardboard documents, domestic use
Box Contents	Laminator, 10 A4 pouches, 10 A5 pouches, 10 business card pouches, manual, warranty card
Dimensions (approx.)	400 x 150 x 100 mm
Weight (approx.)	1.5 kg
Roller Cleaning	With a folded sheet of paper (without pouch)
Safety	Disconnect before cleaning, do not immerse, do not open the housing
Storage	Dry place, away from moisture
Operating Temperature	Automatic preheating up to laminating temperature
Compatible Pouch Type	Pouches for hot or cold lamination according to the mode

Frequently Asked Questions - KH 4410 LAMINATOR LERVIA

How to use the KH 4410 laminator?

To use the laminator, plug it in, turn it on with the ON/OFF switch, select the pouch thickness (80 or 125 microns) or cold mode using the selector. Wait for the green 'Ready' light to come on (and optionally 2-3 additional minutes for a better result). Place the document in a suitable pouch, insert it into the entry slot guiding with the pouch guide, and let the machine feed it automatically. Let the laminated pouch cool for a minute before touching it.

What type of pouches to use?

Use pouches with a maximum width of 230 mm and maximum thickness of 2 x 125 microns (250 microns). For hot lamination, only use pouches designed for hot; for cold lamination, use pouches for cold. The supplied pouches are exclusively for hot lamination.

Why does the green 'Ready' light not turn on?

Check that the device is plugged in and turned on (ON/OFF switch). Make sure the thickness selector is on a position other than 'COLD' for heating. The green light comes on when the operating temperature is reached. If the light still does not turn on, wait a few minutes; if the problem persists, contact customer service.

How to clean the internal rollers?

After use, prepare the device for hot lamination until the green light comes on. Take an A4 sheet of paper folded in half (maximum thickness 1 mm) without a pouch, insert it fold first into the entry slot. Let it pass automatically. Repeat with a clean sheet until no dirt appears on the paper.

Can I laminate glossy photos?

Yes, for glossy photos, select the '125' setting on the selector. This gives a better result with fewer bubbles. Make sure to use a suitable pouch and let the pouch cool under a flat weight.

What to do in case of jam or skewed insertion?

Use the anti-jam system (ABS) by pressing the ABS switch upward. The pouch will be released. Pull it gently outward, then release the switch. Restart lamination ensuring the pouch is centered with the format lock.

Can I laminate cold?

Yes, after letting the device cool if hot lamination has occurred, set the selector to 'COLD' position. Turn on the device and wait for the green light to come on. Use special cold lamination pouches and proceed as for hot lamination.

What is the maximum document thickness for laminating?

The total thickness (document + pouch) must not exceed 1 mm. Beyond this, the pouch may be poorly fed and damage the device or document.

How to avoid the pouch bending or entering skewed?

Use the rear pouch guide and the format lock to center the pouch. Insert it straight into the entry slot. Ensure there is at least 30 cm of free space in front of the device so the pouch comes out completely.

Is the laminator suitable for important or one-of-a-kind documents?

The device is designed for domestic use. Although it complies with safety standards, errors can still occur. It is not recommended to laminate unique or valuable documents, as in case of malfunction, the document could be damaged.

USER MANUAL KH 4410 LAMINATOR LERVIA

Operating Instructions

Laminator KH 4410	Page
1. Intended Use	4
2. Package contents	4
3. Appliance description	4
4. Technical data	4
5. Safety Instructions	5
6. Suitable laminating pouches	6
7. Operating levels	6
8. Preparing for hot lamination	7
9. Preparing for cold lamination	8
10. Lamination process	8
11. Anti block system (ABS)	9
12. Cleaning and care	9
13. Storage	10
14. Disposal	10
15. Warranty & service	10
16. Importer	10

Read the operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference. Hand over the manual to anyone, whom you pass on the appliance to.

Lervia KH 4410

Laminator KH 4410

1. Intended Use

The laminator is intended exclusively for hot and cold lamination of documents of paper or cardboard in private households.

It is not intended for use with other materials. It is also not intended for commercial or industrial use.

No warranty is provided for damages resulting from improper use of the appliance!

2. Package contents

1 Laminator Lervia KH 4410
10 80 micron laminating pouches DIN A4 for hot lamination
10 80 micron laminating pouches DIN A5 for hot lamination
10 80 micron laminating pouches for hot lamination of business cards
1 Operating instructions
1 Warranty card

3. Appliance description

Pouch guide (rear)
2 Pouch format lock
3 LED indicator light "Ready" OK
4 ON/OFFLEDindicatorlight
ON/OFF switch
Selector switch for pouch thickness and cold lamination
Pouch ejector slot (front)
3 Anti block (ABS) switch
Slot for manual pouch input

4. Technical data

Mains voltage: 220-240 V\~, 50 Hz

Rated output: 308 W

Laminating speed: approx. 0.4m /minute

Lamination thickness: max. 1 mm

Pouch width: max. 230 mm

Pouch thickness: max. 2 × 125 (250)

micron

5. Safety Instructions

• Do not allow children handle electronic appliances unsupervised, as they may not always be able to assess the possible injury hazards.
• Unplug the power cord after every use and before cleaning, so as to prevent the appliance from switching on inadvertently.
• Check the appliance and all the parts for visible damages. The safety concept can work only if the appliance is in an immaculate condition.
• Never perform hot lamination on flammable, heat-sensitive and/or meltable materials and do not laminate drawings on temperature-sensitive paper or material that will undergo changes in colour or quality when subjected to heat.
• Never laminate valuable, unique documents. Although the laminator satisfies all typical safety norms and standards, errors can never be completely prevented - as with all electrical appliances. Errors with the laminator can result in damage to the document being laminated.
• Do not laminate any materials with pouch in a thickness greater than 1.0 mm. Otherwise, the laminating pouch can be angled incorrectly inside the device. This can damage the laminating pouch, the document being laminated as well as the laminator.

Danger of electrical shock!

• Connect the appliance to a power socket with a mains voltage of 220 - 240V /50Hz
• Do not operate the appliance with damaged connecting cable or power plug.
• Get customer service to repair or replace connecting cables and/or appliances that are not functioning properly or have been damaged.
• Never immerse the appliance in water. Just wipe it with a damp cloth.
• Do not expose the appliance to the rain and never use it in a humid or wet environment.
• Make sure that the power cord does not become wet during operation.
• Unplug the appliance immediately after use. The appliance is completely disconnected, only when you pull out the power plug from the power socket.
• Do not open or repair the appliance casing yourself. In this case, the appliance is not safe and the warranty is voided.

Fire hazard!

• Do not use the appliance near hot surfaces.
• Do not keep the appliance in places that are exposed to direct sunlight, as this could lead to overheating and cause irreparable damage.
• Do not leave the appliance unattended when in use.
• Never cover the ventilation slits on the top of the appliance while it is on.

Injury hazard!

• Keep children away from the connecting cable and the appliance. Children frequently underestimate the danger from electrical appliances.
• Make sure to find a safe place for the appliance.
• Do not operate the appliance if it has sustained a fall or is damaged. Get the appliance checked and repaired by experts, if necessary.
• Some parts of the appliance become very hot during operation. To avoid burns, do not touch these parts.

6. Suitable laminating pouches

• You can use laminating pouches with a width of up to 230mm and a thickness of max. 2x 125 (250) micron.
• Please note that each laminating pouch may only be used once for laminating.

For hot lamination, use only laminating pouches that are expressly intended for hot lamination. For cold lamination, use only laminating pouches that are expressly intended for cold lamination.
① Note that the laminating pouches included with the laminator are intended exclusively for hot lamination.

7. Operating levels

Switch setting	Laminating pouch thickness
80	> 60 - 80
Cold	to 200
125	85 - 125

Tip: For high-gloss photos, select the switch setting "125".

8. Preparing for hot lamination

Insert the pouch guide 1 into the holes on the back side of the laminator.
Insert the power plug of the laminator into a power socket.
Be sure to find a stabile location for the appliance.
→ Switch on the appliance by flipping the ON/OFF switch ① ⑤. The red ON/OFF LED indicator light ④ turns on.
Set the selector switch for the pouch thickness and cold lamination 6 to the desired pouch thickness (80 or 125 micron). The laminator now heats up to the operating temperature.
- As soon as the green LED indicator light "Ready" OK lights up, the laminator has reached its operating temperature.

① As soon as the operating temperature is reached, the green LED indicator light "Ready" OK will light up. For a more even laminating result, we recommend that you only begin the laminating process after waiting for an additional approx. 2-3 minutes, particularly when using thinner pouches (less than 125 micron), or when adjusting a different pouch thickness.
→ Lay the document to be laminated into a laminating pouch of the appropriate size.

① Make certain that all corners of the document have at least two millimetres of space to the edge of the laminating pouch as shown in Fig. 1. Make certain that you only use a single pouch for laminating. Open it up first, as shown in Fig. 2.

Fig. 1

For information about the lamination process, please read section 10.

Fig. 2

9. Preparing for cold lamination

If you have previously performed hot lamination: Allow the laminator to cool completely after hot lamination before you begin the cold lamination. Otherwise the rolls inside the laminator are still hot. This can damage the laminating pouch and the document to be laminated!
Insert the pouch guide 1 into the holes on the back side of the laminator.
Insert the power plug of the laminator into a power socket.
Be sure to find a stabile location for the appliance.
→ Switch on the appliance by flipping the ON/OFF switch ① ⑤. The red ON/OFF LED indicator light ④ turns on.
Set the selector switch for pouch thickness and cold lamination to "COLD".
- As soon as the green LED indicator light "Ready" ③ lights up, you can begin the cold lamination.
→ Lay the document to be laminated into a laminating pouch of the appropriate size.
Make certain that all corners of the document have at least two millimetres of space to the edge of the laminating pouch as shown in Fig. 1.

(1) Make certain that you only use a single pouch for laminating. Open it up first, as shown in Fig. 2.
For information about the lamination process, please read section 10.

10. Lamination process

Lay the laminating pouch onto the pouch guide ①. Lay the right or left edge of the laminating pouch against the pouch format lock ② (closed side first). Slide the pouch format lock together until the selected format is reached. This prevents the laminating pouch from being pulled in at an angle.
If the pouch is still pulled in at an angle, use the "Anti block system" as described in section 11.
Now slide the laminating pouch slowly into the slot for manual pouch input 9.
When you have slid the laminating pouch several centimetres into the slot, it will be pulled in automatically. Let go of the laminating pouch as soon as you notice that it is being pulled in automatically.

Make certain that there is at least 30 cm of open space in front of the laminator. Otherwise the laminating pouch will not be output completely from the laminator after lamination. This could damage the laminated pouch.
The laminated pouch is output from the pouch ejector slot of the laminator.
(1) (Only after hot lamination) When the laminated pouch is output from the pouch ejector slot of the laminator, it is still hot and its shape may change slightly. For this reason, let the laminated pouch cool for one minute before touching it. To improve the lamination result, you can weigh down the still hot laminated pouch with a book, a file folder or another heavy, flat object. This achieves a flat, flawless surface.

11. Anti block system (ABS)

At the start of the lamination process, the pouch may be pulled in at an angle or jam up inside the appliance.

Press the Anti block switch (ABS) 8 upward.
The pouch is then released again.
Pull out the pouch, then release the Anti block switch 8.
Start the lamination process over.

12. Cleaning and care

Life-threatening danger of electrical shock:

• Never open the appliance housing. There are no operating elements inside.
• Never immerse the appliance components into water or other liquids!

Cleaning the casing:

Clean the surface of the casing with a slightly damp wash cloth.
First pull the power plug.
Let the appliance cool down completely.
Make certain that no moisture enters into the inside of the appliance.

Lervia KH 4410

Cleaning the inside of the appliance:

With every lamination, contaminants are deposited on the rollers inside the laminator. Over time, this reduces the performance of the laminator. You should therefore clean the rollers inside the laminator after use.

Prepare the appliance as described in section 8 "Hot lamination" until the green LED indicator light "Ready" ③ OK lights up.
Then run a sheet of DIN A4 paper folded in the middle (maximum thickness 1.0mm ) ...

• without a laminating pouch and
  with the fold first

... slowly into the slot for manual pouch input 9.

Let go of the sheet as soon as you notice that it is being pulled in automatically.
- The contaminants on the rollers inside the laminator are now transferred to the sheet of paper. The paper is output from the pouch ejector slot ① of the laminator.
Repeat the cleaning several times. Each time, use a new, clean sheet of paper. If you no longer see any contaminants on the paper, the rollers inside the laminator are clean.

13. Storage

Let the appliance cool off completely before storing it.

① Do not store the laminator in damp locations as moisture could enter inside the appliance. (E.g. cellars)!

14. Disposal

Do not dispose of the device in normal domestic waste.

Dispose of the device over a registered waste disposal firm or through your communal waste disposal facility. Observe the currently valid regulations. In case of doubt, consult your waste disposal facility.

15. Warranty & service

The warranty conditions and the service address can be found on the warranty slip.

16. Importer

Komperna GmbH

Burgstrasse 21

D-44867 Bochum

www.kompernass.com

Lervia KH 4410